{"id":2141,"date":"2019-07-22T03:02:08","date_gmt":"2019-07-22T03:02:08","guid":{"rendered":"http:\/\/wiki.thomasandsofia.com\/?p=2141"},"modified":"2021-12-13T13:16:16","modified_gmt":"2021-12-13T13:16:16","slug":"section-15-cisco-device-management","status":"publish","type":"post","link":"https:\/\/wiki.thomasandsofia.com\/?p=2141","title":{"rendered":"Section 15: Cisco Device Management"},"content":{"rendered":"<p><a href=\"http:\/\/wiki.thomasandsofia.com\/?p=2126\">&lt; Section 14<\/a> | <a href=\"\/course-introduction\/\">Home<\/a> | <a href=\"http:\/\/wiki.thomasandsofia.com\/?p=2152\">Section 16 &gt;<\/a><br \/>\n<a href=\"\/ccent-quick-notes\/\">Quick Notes<\/a><\/p>\n<p>41% Complete<\/p>\n<h1>83: Cisco Device Management &#8211; Introduction<\/h1>\n<p><a href=\"https:\/\/www.udemy.com\/cisco-icnd1\/learn\/lecture\/8605296#overview\" target=\"_blank\" rel=\"noopener\">https:\/\/www.udemy.com\/cisco-icnd1\/learn\/lecture\/8605296#overview<\/a><\/p>\n<p>CCNA #85: <a href=\"https:\/\/www.udemy.com\/course\/ccna-complete\/learn\/lecture\/7393416#overview\" target=\"_blank\" rel=\"noopener\">https:\/\/www.udemy.com\/course\/ccna-complete\/learn\/lecture\/7393416#overview<\/a><\/p>\n<h1>84: The Boot Up Process<\/h1>\n<p><a href=\"https:\/\/www.udemy.com\/cisco-icnd1\/learn\/lecture\/8605304#overview\" target=\"_blank\" rel=\"noopener\">https:\/\/www.udemy.com\/cisco-icnd1\/learn\/lecture\/8605304#overview<\/a><\/p>\n<h2>Cisco Device Memory<\/h2>\n<ul>\n<li>ROM &#8211; Read Only Memory<\/li>\n<li>Flash\n<ul>\n<li>Similar to a solid state disk.<\/li>\n<li>Retains data even when powered off.\u00a0 Does not require battery<\/li>\n<li>Newer devices use removable CompactFlash<\/li>\n<\/ul>\n<\/li>\n<li>NVRAM &#8211; Non-Volatile RAM\n<ul>\n<li>Battery powered, so it retains its memory even when the device is powered off.<\/li>\n<\/ul>\n<\/li>\n<li>RAM &#8211; Random Access Memory<\/li>\n<li>External USB devices can be used.<\/li>\n<\/ul>\n<h3>ROM Read Only Memory<\/h3>\n<ul>\n<li>Power on self test (POST) checking for any initial errors.<\/li>\n<li>Load the bootstrap<\/li>\n<li>Bootstrap looks in Flash for an IOS image to load\n<ul>\n<li>If Flash image cannot be found, the device will display the ROMMON (ROM Monitor) prompt at the command line.<\/li>\n<li>The ROM Monitor can be used to recover a missing or corrupted software image.\n<ul>\n<li>In this case, you can boot from USB or an external TFTP (Trivial File Transfer Protocol) server<\/li>\n<\/ul>\n<\/li>\n<li>Search for &#8216;Cisco ROMMON Recovery&#8217; for your device model.<\/li>\n<\/ul>\n<\/li>\n<\/ul>\n<h3>Flash Memory<\/h3>\n<ul>\n<li>System will load the first IOS image found in Flash by default<\/li>\n<li>You can override this with the &#8216;boot system&#8217; command\n<ul>\n<li>This is a Global Configuration command<\/li>\n<\/ul>\n<\/li>\n<li>You can copy additional IOS system images to Flash via TFTP or USB<\/li>\n<\/ul>\n<h3>NVRAM Non-Volatile RAM Memory<\/h3>\n<ul>\n<li>Once the system finishes loading the IOS system image from Flash, it will load the startup-config configuration file from NVRAM<\/li>\n<li>The saved startup-config becomes the current running-config in RAM<\/li>\n<li>If no startup-config file is found, the device will load the Setup Wizard.<\/li>\n<li>Whenever you enter a command in IOS, it takes effect immediately and goes into the running-config<\/li>\n<li>To make your changes permanent across a reboot:\n<ul>\n<li>copy running-config startup-config<\/li>\n<\/ul>\n<\/li>\n<\/ul>\n<h3>RAM Random Access Memory<\/h3>\n<ul>\n<li>The IOS image and startup-config are loaded from Flash and NVRAM into RAM during bootup.<\/li>\n<li>RAM is used as the normal working memory of the device<\/li>\n<li>ROM, Flash and NVRAM are permanent memory, their contents are not lost when the device is powered off or rebooted.<\/li>\n<li>RAM is volatile memory.\u00a0 Its contents are lost when the device is powered off.<\/li>\n<\/ul>\n<h2>The VLAN Database<\/h2>\n<ul>\n<li>On a switch, the VLAN database (vlan.dat) is saved in either Flash or NVRAM, depending on the model of the switch.<\/li>\n<\/ul>\n<h2>Booting from TFTP<\/h2>\n<ul>\n<li>The system can also load a system image and\/or startup-config from an external TFTP server instead of Flash\/NVRAM<\/li>\n<li>This is NOT recommended because the device will not be able to boot if it loses connectivity to the server.<\/li>\n<li>It is usually only used where the device does not have enough capacity in Flash to save the system image.<\/li>\n<\/ul>\n<h1>85: The Boot Up Process Lab Demo<\/h1>\n<p><a href=\"https:\/\/www.udemy.com\/cisco-icnd1\/learn\/lecture\/8605310#overview\" target=\"_blank\" rel=\"noopener\">https:\/\/www.udemy.com\/cisco-icnd1\/learn\/lecture\/8605310#overview<\/a><\/p>\n<h2>Lab Example<\/h2>\n<p>Using Packet Tracer<\/p>\n<p><a href=\"http:\/\/wiki.thomasandsofia.com\/wp-content\/uploads\/2019\/07\/boot1.png\"><img loading=\"lazy\" decoding=\"async\" class=\"alignnone size-full wp-image-2142\" src=\"http:\/\/wiki.thomasandsofia.com\/wp-content\/uploads\/2019\/07\/boot1.png\" alt=\"\" width=\"421\" height=\"145\" srcset=\"https:\/\/wiki.thomasandsofia.com\/wp-content\/uploads\/2019\/07\/boot1.png 421w, https:\/\/wiki.thomasandsofia.com\/wp-content\/uploads\/2019\/07\/boot1-300x103.png 300w, https:\/\/wiki.thomasandsofia.com\/wp-content\/uploads\/2019\/07\/boot1-150x52.png 150w\" sizes=\"auto, (max-width: 421px) 100vw, 421px\" \/><\/a><\/p>\n<p>Delete the system image &#8211; <strong><span style=\"color: #ff0000;\">This is UGLY!!<\/span><\/strong><\/p>\n<pre>show flash:\r\n\r\nDirectory of flash:\/\r\n\r\n    2  -rwx     3722814  Mar 01 1993 00:08:12 +00:00  c2950-i6k2l2q4-mz.121-22.EA14.bin\r\n\r\n# delete the file\r\ndelete flash:c2950-i6k2l2q4-mz.121-22.EA14.bin\r\nDelete filename [c2950-i6k2l2q4-mz.121-22.EA14.bin]? &lt;enter&gt;\r\nDelete flash:c2950-i6k2l2q4-mz.121-22.EA14.bin? [confirm] &lt;enter&gt;\r\n# system will continue running until you reboot\r\n# Reboot the system\r\nreload<\/pre>\n<h2>Reboot the system<\/h2>\n<h3>Switch<\/h3>\n<p><a href=\"https:\/\/www.cisco.com\/c\/en\/us\/support\/docs\/switches\/catalyst-2950-series-switches\/41845-192.html\" target=\"_blank\" rel=\"noopener\">https:\/\/www.cisco.com\/c\/en\/us\/support\/docs\/switches\/catalyst-2950-series-switches\/41845-192.html<\/a><\/p>\n<p><a href=\"https:\/\/www.freeccnaworkbook.com\/workbooks\/ccna\/recovering-a-corrupt-cisco-ios-image-on-a-catalyst-switch\" target=\"_blank\" rel=\"noopener\">https:\/\/www.freeccnaworkbook.com\/workbooks\/ccna\/recovering-a-corrupt-cisco-ios-image-on-a-catalyst-switch<\/a><\/p>\n<h3>Router<\/h3>\n<pre>The system is unable to boot automatically. The BOOT\r\nenvironment variable needs to be set to a bootable\r\nimage.\r\nswitch: IP_ADDRESS=10.10.10.5\r\nIP_SUBNET_MASK=255.255.255.0\r\nDEFAULT_GATEWAY=10.10.10.1\r\nTFTP_SERVER=10.10.10.20\r\nTFTP_FILE=c2950-i6k2l2q4-mz.121-22.EA14.bin<\/pre>\n<p>&nbsp;<\/p>\n<p>Summary: he deleted the IOS from flash, searched for his devices &#8216;cisco ROMMON recovery&#8217; and found the required commands to configure the system to locate the TFTP server and download the IOS.<\/p>\n<ul>\n<li><span style=\"color: #ff0000;\"><strong>ROMMON commands are CASE SENSITIVE!!!<\/strong><\/span><\/li>\n<\/ul>\n<h1>86: Factory Reset and Password Recovery<\/h1>\n<p><a href=\"https:\/\/www.udemy.com\/cisco-icnd1\/learn\/lecture\/8605312#overview\" target=\"_blank\" rel=\"noopener\">https:\/\/www.udemy.com\/cisco-icnd1\/learn\/lecture\/8605312#overview<\/a><\/p>\n<h2>Factory Reset<\/h2>\n<ul>\n<li>write erase<\/li>\n<li>This will erase the startup-config<\/li>\n<li>Reload to boot up with a blank configuration<\/li>\n<li>The Setup Wizard will run at next boot.<\/li>\n<\/ul>\n<h2>The Config Register<\/h2>\n<ul>\n<li>The configuration register can be used to change the way the router boots<\/li>\n<li>use the &#8216;config-register&#8217; command from global configuration mode (config), or &#8216;confreg&#8217; from the ROMMON prompt.<\/li>\n<li>Example: config-register 0x2142\n<ul>\n<li>0x2102: boot normally (default)<\/li>\n<li>0x2120: boot into ROMMON<\/li>\n<li>0x2142: ignore contents of NVRAM (Startup-config)<\/li>\n<li>There are more!<\/li>\n<\/ul>\n<\/li>\n<\/ul>\n<h2>Router Password Recovery Procedure<\/h2>\n<h3>Part 1 &#8211; Access the enable prompt<\/h3>\n<ul>\n<li>Press &lt;Ctrl&gt;+&lt;Break&gt; at power on to break into rommon prompt\n<ul>\n<li>&lt;Ctrl&gt; +&lt;A&gt; then &lt;F&gt; for minicom!<\/li>\n<\/ul>\n<\/li>\n<li>Enter &#8216;confreg 0x2142&#8217; to ignore the startup-config on boot.\n<ul>\n<li>The startup-config is still there with the full configuration including the unknown enable secret, but the router does not use it when it boots.<\/li>\n<\/ul>\n<\/li>\n<li>Enter &#8216;reset&#8217; to reload<\/li>\n<li>The router will boot up with no configuration.\n<ul>\n<li>Type &#8216;no&#8217; to bypass the setup wizard<\/li>\n<\/ul>\n<\/li>\n<li>Enter enable mode.\u00a0 You will not be prompted for the enable secret as it is not in the running configuration.<\/li>\n<\/ul>\n<h3>Part 2 &#8211; Reload the startup-config<\/h3>\n<ul>\n<li>Copy the startup-config to the running-config\n<ul>\n<li>DO NOT FORGET THIS STEP!<\/li>\n<li>This will copy the entire previous configuration into the running config, inclnonouding the unknown enable secret.\u00a0 Since you are already in enable mode, you don&#8217;t need to know what it is.<\/li>\n<\/ul>\n<\/li>\n<li>Enter a new enable secret in global configuration mode. to over write the old one.\u00a0 This will go into the running-config.<\/li>\n<li>Enter &#8216;config-register 0x2102&#8217; so the router will boot normally on the next restart.<\/li>\n<li>Enter &#8216;copy running-config startup-config&#8217; to save the new enable secret.<\/li>\n<\/ul>\n<h2>Switch Password Recovery Procedure<\/h2>\n<ul>\n<li>Likely very similar to the router password recovery procdure, but you may have to physically press the &#8216;Mode&#8217; button on the front of the switch to break into the switch loader.<\/li>\n<li>Search for &#8216;Cisco Password recovery&#8217; for your model of switch for full instructions.<\/li>\n<\/ul>\n<h1>87: Password Recovery Lab Demo<\/h1>\n<p><a href=\"https:\/\/www.udemy.com\/cisco-icnd1\/learn\/lecture\/8605314#overview\" target=\"_blank\" rel=\"noopener\">https:\/\/www.udemy.com\/cisco-icnd1\/learn\/lecture\/8605314#overview<\/a><\/p>\n<p>Lots of fun in this lecture.\u00a0 Pay attention and see if you can catch his mistakes before he tells you he made them.<\/p>\n<h1>88: Backing Up the System Image and Configuration<\/h1>\n<p><a href=\"https:\/\/www.udemy.com\/cisco-icnd1\/learn\/lecture\/8605320#overview\" target=\"_blank\" rel=\"noopener\">https:\/\/www.udemy.com\/cisco-icnd1\/learn\/lecture\/8605320#overview<\/a><\/p>\n<h2>Caution &#8211; do not perform this at home!<\/h2>\n<p>It will take several hours to restore a system image if you delete it.<\/p>\n<p><a href=\"\/recover-missing-ios-on-cisco-catalyst-2950-switch\/\">Recover a Cisco 2950 switch<\/a><\/p>\n<h2>Backing up the System Image and Config<\/h2>\n<ul>\n<li>Copies of the device&#8217;s IOS system image and configuration can be saved to Flash FTO, TFTP or USB<\/li>\n<li>If you copy a config file into the running-config, it will be merged with the new configuration.\n<ul>\n<li><strong>This seems incorrect, but who am I to know<\/strong>.<\/li>\n<\/ul>\n<\/li>\n<li>To replace a configuration, factory reset and then copy the new configuration into the startup-config<\/li>\n<\/ul>\n<h3>Common commands<\/h3>\n<ul>\n<li>Backup files from Flash to TFTP\n<ul>\n<li>copy flash tftp\n<ul>\n<li>You will be prompted for the file name.<\/li>\n<li>You will be prompted for the tftp server&#8217;s IP address<\/li>\n<li>You will need to enter a file name that you&#8217;re saving as.\u00a0 It is recommended to enter the same name.<\/li>\n<\/ul>\n<\/li>\n<\/ul>\n<\/li>\n<li>Backup the running-config to TFTP\n<ul>\n<li>copy running-config tftp\n<ul>\n<li>You will be prompted for the tftp server&#8217;s IP address<\/li>\n<li>You will need to enter a file name that you&#8217;re saving as.\u00a0 This time it is recommended to incorporate a save date.<\/li>\n<\/ul>\n<\/li>\n<\/ul>\n<\/li>\n<li>Backup the startup-config to USB\n<ul>\n<li>copy startup-config usb<\/li>\n<\/ul>\n<\/li>\n<li>Restore a saved backup\n<ul>\n<li>To the Startup Config\n<ul>\n<li>(config)#write erase<\/li>\n<li>#copy flash start\n<ul>\n<li>Enter the complete filename as saved in flash<\/li>\n<li>Press [Enter] when prompted to save as startup-config<\/li>\n<\/ul>\n<\/li>\n<li>#reload<\/li>\n<\/ul>\n<\/li>\n<li>To the running config\n<ul>\n<li>#copy flash run\n<ul>\n<li>Enter the complete filename as saved in flash<\/li>\n<li>Press [Enter] when prompted to save as startup-config<\/li>\n<\/ul>\n<\/li>\n<\/ul>\n<\/li>\n<\/ul>\n<\/li>\n<\/ul>\n<h1>89: Upgrading IOS<\/h1>\n<p><a href=\"https:\/\/www.udemy.com\/cisco-icnd1\/learn\/lecture\/8605324#overview\" target=\"_blank\" rel=\"noopener\">https:\/\/www.udemy.com\/cisco-icnd1\/learn\/lecture\/8605324#overview<\/a><\/p>\n<p>Upgrading the IOS System Image<\/p>\n<ul>\n<li>IOS software images can be downloaded from: <a href=\"https:\/\/software.cisco.com\" target=\"_blank\" rel=\"noopener\">https:\/\/software.cisco.com<\/a><\/li>\n<li>After downloading, copy the file to the device&#8217;s flash using TFTP\n<ul>\n<li>copy tftp flash<\/li>\n<li>Delete the old system image or use the &#8216;boot system&#8217; command\n<ul>\n<li>(config)#boot system flash:&lt;full file name&gt;<\/li>\n<\/ul>\n<\/li>\n<\/ul>\n<\/li>\n<li>Make sure you &#8216;reload&#8217; to ensure you reboot to the new version.<\/li>\n<\/ul>\n<h1>90: Licensing<\/h1>\n<p><a href=\"https:\/\/www.udemy.com\/cisco-icnd1\/learn\/lecture\/8605326#overview\" target=\"_blank\" rel=\"noopener\">https:\/\/www.udemy.com\/cisco-icnd1\/learn\/lecture\/8605326#overview<\/a><\/p>\n<h2>Router IOS Licensing<\/h2>\n<ul>\n<li>Prior to IOS 15.0, different IOS system images were available for different feature sets, such as Security (firewall or IPS) or Telephony.\n<ul>\n<li>Licensing was not enforced.<\/li>\n<\/ul>\n<\/li>\n<li>A universal system image is provided from IOS 15.0<\/li>\n<li>License codes must be entered to activate the Technology Packages<\/li>\n<\/ul>\n<h2>Licensing Procedure<\/h2>\n<p><span style=\"color: #ff0000;\"><strong>IMPORTANT! You will be tested on this!<\/strong><\/span><\/p>\n<ul>\n<li>When you purchase a license you will be provided with a Product Activation Key (PAK) code<\/li>\n<li>The license will be tied to an individual device.\u00a0 To get the device&#8217;s Unique Device Identifier (UDI) enter:\n<ul>\n<li>show license udi<\/li>\n<\/ul>\n<\/li>\n<li>Go to the Cisco License portal <a href=\"http:\/\/www\/cisco.com\/go\/license\" target=\"_blank\" rel=\"noopener\">http:\/\/www\/cisco.com\/go\/license<\/a> and enter the PAK code and UDI to generate the license.<\/li>\n<li>Copy the license to Flash on the router using TFTP or similar, then activate it as shown below\n<ul>\n<li>license install flash:<\/li>\n<li>license show<\/li>\n<\/ul>\n<\/li>\n<\/ul>\n<h1>91: Cisco Device Management &#8211; Lab Exercises<\/h1>\n<p><a href=\"https:\/\/www.udemy.com\/cisco-icnd1\/learn\/lecture\/8605328#overview\" target=\"_blank\" rel=\"noopener\">https:\/\/www.udemy.com\/cisco-icnd1\/learn\/lecture\/8605328#overview<\/a><\/p>\n<ul>\n<li>Basically just copying files back and forth using tftp<\/li>\n<li>Restoring Startup Config<\/li>\n<\/ul>\n<pre># erase all files in nvram\r\nwrite erase\r\n# now copy the restore\r\ncopy &lt;flash\/tftp&gt; start\r\n# enter the file to copy\r\n# Destination filename startup-config\r\nreload<\/pre>\n<p><a href=\"http:\/\/wiki.thomasandsofia.com\/wp-content\/uploads\/2019\/07\/15-Cisco-Device-Management.jpg\"><img loading=\"lazy\" decoding=\"async\" class=\"alignnone size-full wp-image-2147\" src=\"http:\/\/wiki.thomasandsofia.com\/wp-content\/uploads\/2019\/07\/15-Cisco-Device-Management.jpg\" alt=\"\" width=\"924\" height=\"393\" srcset=\"https:\/\/wiki.thomasandsofia.com\/wp-content\/uploads\/2019\/07\/15-Cisco-Device-Management.jpg 924w, https:\/\/wiki.thomasandsofia.com\/wp-content\/uploads\/2019\/07\/15-Cisco-Device-Management-300x128.jpg 300w, https:\/\/wiki.thomasandsofia.com\/wp-content\/uploads\/2019\/07\/15-Cisco-Device-Management-768x327.jpg 768w, https:\/\/wiki.thomasandsofia.com\/wp-content\/uploads\/2019\/07\/15-Cisco-Device-Management-150x64.jpg 150w\" sizes=\"auto, (max-width: 924px) 100vw, 924px\" \/><\/a><\/p>\n<p><a href=\"http:\/\/wiki.thomasandsofia.com\/wp-content\/uploads\/2019\/07\/15-Cisco-Device-Management-Lab-Exercise.pdf\">15 Cisco Device Management Lab Exercise<\/a><\/p>\n<p><a href=\"http:\/\/wiki.thomasandsofia.com\/wp-content\/uploads\/2019\/07\/15-Cisco-Device-Management-Answer-Key.pdf\">15 Cisco Device Management Answer Key<\/a><\/p>\n<p>c2900-universalk9-mz.SPA.151-4.M4.bin<\/p>\n<p>c2960-lanbasek9-mz.150-2.SE4.bin<\/p>\n<p>&nbsp;<\/p>\n<p>&nbsp;<\/p>\n<p>&nbsp;<\/p>\n<p>&nbsp;<\/p>\n<p>&nbsp;<\/p>\n<p>&nbsp;<\/p>\n<p>&nbsp;<\/p>\n<p>&nbsp;<\/p>\n<p>&nbsp;<\/p>\n<p>&nbsp;<\/p>\n","protected":false},"excerpt":{"rendered":"<p>&lt; Section 14 | Home | Section 16 &gt; Quick Notes 41% Complete 83: Cisco Device Management &#8211; Introduction https:\/\/www.udemy.com\/cisco-icnd1\/learn\/lecture\/8605296#overview CCNA #85: https:\/\/www.udemy.com\/course\/ccna-complete\/learn\/lecture\/7393416#overview 84: The Boot Up Process https:\/\/www.udemy.com\/cisco-icnd1\/learn\/lecture\/8605304#overview Cisco Device Memory ROM &#8211; Read Only Memory Flash Similar to a solid state disk. Retains data even when powered off.\u00a0 Does not require battery Newer ..<\/p>\n<div class=\"clear-fix\"><\/div>\n<p><a href=\"https:\/\/wiki.thomasandsofia.com\/?p=2141\" title=\"read more...\">Read more<\/a><\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[45],"tags":[],"class_list":["post-2141","post","type-post","status-publish","format-standard","hentry","category-icnd1-ccent"],"_links":{"self":[{"href":"https:\/\/wiki.thomasandsofia.com\/index.php?rest_route=\/wp\/v2\/posts\/2141","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/wiki.thomasandsofia.com\/index.php?rest_route=\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/wiki.thomasandsofia.com\/index.php?rest_route=\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/wiki.thomasandsofia.com\/index.php?rest_route=\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/wiki.thomasandsofia.com\/index.php?rest_route=%2Fwp%2Fv2%2Fcomments&post=2141"}],"version-history":[{"count":17,"href":"https:\/\/wiki.thomasandsofia.com\/index.php?rest_route=\/wp\/v2\/posts\/2141\/revisions"}],"predecessor-version":[{"id":3608,"href":"https:\/\/wiki.thomasandsofia.com\/index.php?rest_route=\/wp\/v2\/posts\/2141\/revisions\/3608"}],"wp:attachment":[{"href":"https:\/\/wiki.thomasandsofia.com\/index.php?rest_route=%2Fwp%2Fv2%2Fmedia&parent=2141"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/wiki.thomasandsofia.com\/index.php?rest_route=%2Fwp%2Fv2%2Fcategories&post=2141"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/wiki.thomasandsofia.com\/index.php?rest_route=%2Fwp%2Fv2%2Ftags&post=2141"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}