{"id":1973,"date":"2019-06-19T22:35:19","date_gmt":"2019-06-19T22:35:19","guid":{"rendered":"http:\/\/wiki.thomasandsofia.com\/?p=1973"},"modified":"2020-05-06T00:10:04","modified_gmt":"2020-05-06T00:10:04","slug":"how-to-setup-the-lab","status":"publish","type":"post","link":"https:\/\/wiki.thomasandsofia.com\/?p=1973","title":{"rendered":"Section 2: How to setup the lab"},"content":{"rendered":"<p><a href=\"http:\/\/wiki.thomasandsofia.com\/?p=1970\">&lt; Section 1<\/a> | <a href=\"http:\/\/wiki.thomasandsofia.com\/?p=1980\">Section 3 &gt;<\/a><\/p>\n<h1>7. Introduction<\/h1>\n<p><a href=\"https:\/\/www.udemy.com\/cisco-icnd1\/learn\/lecture\/14693648#overview\" target=\"_blank\" rel=\"noopener\">https:\/\/www.udemy.com\/cisco-icnd1\/learn\/lecture\/14693648#overview<\/a><\/p>\n<p>GNS3 and Packet Tracer<br \/>\nGNS3<\/p>\n<ul>\n<li>Routing emulator\n<ul>\n<li>Runs the actual IOS<\/li>\n<\/ul>\n<\/li>\n<li>Not good with switching<\/li>\n<\/ul>\n<p>Packet Tracer<\/p>\n<ul>\n<li>Full featured support for switching<\/li>\n<li>Is a simulator not running real IOS software.\n<ul>\n<li>Does not run the full set of commands<\/li>\n<\/ul>\n<\/li>\n<\/ul>\n<p>Comments on how to run labs.<\/p>\n<h1>8. GNS3 Installation and Configuration<\/h1>\n<p>https:\/\/www.udemy.com\/cisco-icnd1\/learn\/lecture\/8589112#overview<\/p>\n<p>GNS3 Download<\/p>\n<ul>\n<li>New: <a href=\"https:\/\/github.com\/GNS3\/gns3-gui\/releases\/tag\/v2.0.3\" target=\"_blank\" rel=\"noopener\">https:\/\/github.com\/GNS3\/gns3-gui\/releases\/tag\/v2.0.3<\/a><\/li>\n<li>Old: <a href=\"https:\/\/www.gns3.com\/\" target=\"_blank\" rel=\"noopener\">https:\/\/www.gns3.com\/<\/a><\/li>\n<\/ul>\n<p>Notes for install:<\/p>\n<ul>\n<li>Uncheck WireShark.\n<ul>\n<li>Something with the installer causes that to fail.<\/li>\n<li>Leave the rest<\/li>\n<\/ul>\n<\/li>\n<li>The software takes several minutes to install.<\/li>\n<li>SolarWinds standard tool kit is not required, so OK to not install.<\/li>\n<\/ul>\n<p>At Software startup<\/p>\n<ul>\n<li>( * ) Run only legacy IOS on my computer<\/li>\n<li>Local server configuration\n<ul>\n<li>Change the Host Binding to 127.0.0.1 [ Next ]<\/li>\n<\/ul>\n<\/li>\n<li>Connection to local server was successful [ Next ]<\/li>\n<li>[Finish]<\/li>\n<\/ul>\n<p>Add an appliance<\/p>\n<ul>\n<li>Download the IOS image\n<ul>\n<li>Search &#8216;cisco software download&#8217;\n<ul>\n<li>Cisco Software Center: <a href=\"https:\/\/software.cisco.com\/\" target=\"_blank\" rel=\"noopener\">http:\/\/software.cisco.com<\/a><\/li>\n<li><a href=\"https:\/\/drive.google.com\/file\/d\/1pQyF8sz2PLUJdZvuasWNCXRixjPWDz6U\/view\" target=\"_blank\" rel=\"noopener\">c7200-advipservicesk9-mz-152-4.S5.bin<\/a><\/li>\n<\/ul>\n<\/li>\n<\/ul>\n<\/li>\n<li>Download the GNS3 IOS Image\n<ul>\n<li>Search &#8216;gns3 ios images&#8217;\n<ul>\n<li><a href=\"http:\/\/srijit.com\/working-cisco-ios-gns3\/\" target=\"_blank\" rel=\"noopener\">http:\/\/srijit.com\/working-cisco-ios-gns3\/<\/a><\/li>\n<li>Download the image for the 7200 v15: <a href=\"http:\/\/i.srijit.com\/CiscoIOS-GNS3\" target=\"_blank\" rel=\"noopener\">http:\/\/i.srijit.com\/CiscoIOS-GNS3<\/a>\n<ul>\n<li>c7200-advipservicesk9-mz-152-4.S5.bin<\/li>\n<li>NOT the 7200p !<\/li>\n<\/ul>\n<\/li>\n<li>Download the image for the 3245 also.\u00a0 (Same link)\n<ul>\n<li>c3745-advipservicesk9-mz.124-25d.bin<\/li>\n<\/ul>\n<\/li>\n<\/ul>\n<\/li>\n<\/ul>\n<\/li>\n<li>Return to GNS3\n<ul>\n<li>New Appliance Template\n<ul>\n<li>( * ) Add an IOS router using a real IOS image (supported by Dynamips)<\/li>\n<li>[ OK ]<\/li>\n<\/ul>\n<\/li>\n<li>IOS image\n<ul>\n<li>Browse to your c7200 file and select.<\/li>\n<li>&#8216;Would you like to decompress this image?&#8217; &#8211; [ Yes ]<\/li>\n<li>[ Next ]<\/li>\n<\/ul>\n<\/li>\n<li>Name and Platform\n<ul>\n<li>Keep defaults<\/li>\n<li>[ Next ]<\/li>\n<\/ul>\n<\/li>\n<li>Memory\n<ul>\n<li>Accept default (512)<\/li>\n<li>[ Next ]<\/li>\n<\/ul>\n<\/li>\n<li>Network Adaptors\n<ul>\n<li>Slot 0: C7200-IO-FE (Default)<\/li>\n<li>Slots 1, 2 and 3: PA- FE-TX<\/li>\n<li>[ Next ]<\/li>\n<\/ul>\n<\/li>\n<li>Idle PC\n<ul>\n<li>Click the [Idle PC Finder] button for Idle PC next to the green bar\n<ul>\n<li>The system will run a few tests.\u00a0 This takes about a minute or so.<\/li>\n<li>Clcik [OK] when it finds a suitable value<\/li>\n<\/ul>\n<\/li>\n<li>[ Finish ]<\/li>\n<\/ul>\n<\/li>\n<\/ul>\n<\/li>\n<li>Now we need to install the C3745<\/li>\n<li>Preferences &gt; IOS routers: IOS router templates &gt; [ New ]\n<ul>\n<li>IOS Image\n<ul>\n<li>( * ) New Image<\/li>\n<li>Browse for the c3745 image and repeat the steps above for the c7200\n<ul>\n<li>For Interface slots 1, 2 and 3 select the NM-1FE-TX<\/li>\n<\/ul>\n<\/li>\n<\/ul>\n<\/li>\n<li>WIC Modules\n<ul>\n<li>leave defaults (blanks)<\/li>\n<li>[ Next ]<\/li>\n<\/ul>\n<\/li>\n<li>Idle PC finder &#8211; Yes!<\/li>\n<li>Return to the IOS router templates screen and click [ OK ]<\/li>\n<\/ul>\n<\/li>\n<\/ul>\n<p>Starting a project<\/p>\n<ul>\n<li>When prompted to start a new project, do not.\u00a0 Close the program.\u00a0 When needed, you&#8217;ll double click the project file &#8216;.gsn3project&#8217; and the software will open with the project loaded for you.<\/li>\n<\/ul>\n<h1>9. Installation and setup for Cisco PacketTracer<\/h1>\n<p><a href=\"https:\/\/www.udemy.com\/cisco-icnd1\/learn\/lecture\/8589196#questions\/4413460\" target=\"_blank\" rel=\"noopener\">https:\/\/www.udemy.com\/cisco-icnd1\/learn\/lecture\/8589196#questions\/4413460<\/a><\/p>\n<ul>\n<li>Download from <a href=\"http:\/\/www.netacad.com\/campaign\/ptdt-4\/\" target=\"_blank\" rel=\"noopener\">http:\/\/www.netacad.com\/campaign\/ptdt-4\/<\/a>\n<ul>\n<li>You&#8217;ll need to enroll with your name and email address.\n<ul>\n<li>and a lot of other info \ud83d\ude41<\/li>\n<\/ul>\n<\/li>\n<li>Close the Start Class popup if prompted<\/li>\n<li>Check your email and confirm your email address<\/li>\n<li>Resources &gt; Download PacketTracer<\/li>\n<li>Extract the zip file and double click the .exe setup program\n<ul>\n<li>Accept any defaults<\/li>\n<li>Installation takes &lt; 1 minute<\/li>\n<li>You may need to restart your computer to contine<\/li>\n<\/ul>\n<\/li>\n<li>At first run, you may need to log in with your email address and password used to enrole in the netacad program.<\/li>\n<\/ul>\n<\/li>\n<\/ul>\n<p>&nbsp;<\/p>\n<h1 class=\"a1 mb-space-md\">10. GNS3 and Packet Tracer Installation Notes and FAQ<\/h1>\n<div class=\"asset-container\">\n<div class=\"article-asset--article-content--1MwHd\">\n<p><strong>Where can I download the software?<\/strong><\/p>\n<p>GNS3:\u00a0<a href=\"https:\/\/www.gns3.com\/software\" target=\"_blank\" rel=\"nofollow noopener\">https:\/\/www.gns3.com\/software<\/a><\/p>\n<p>Packet Tracer:\u00a0Enroll in the \u2018Introduction to Packet Tracer\u2019 course at <a href=\"https:\/\/www.netacad.com\/campaign\/ptdt-4\" target=\"_blank\" rel=\"nofollow noopener\">https:\/\/www.netacad.com\/campaign\/ptdt-4<\/a><\/p>\n<p>Then go to <a href=\"https:\/\/www.netacad.com\/\" target=\"_blank\" rel=\"nofollow noopener\">https:\/\/www.netacad.com<\/a>, click on \u2018Resources\u2019 near the top-right corner then \u2018Download Packet Tracer\u2019<\/p>\n<\/div>\n<\/div>\n","protected":false},"excerpt":{"rendered":"<p>&lt; Section 1 | Section 3 &gt; 7. Introduction https:\/\/www.udemy.com\/cisco-icnd1\/learn\/lecture\/14693648#overview GNS3 and Packet Tracer GNS3 Routing emulator Runs the actual IOS Not good with switching Packet Tracer Full featured support for switching Is a simulator not running real IOS software. Does not run the full set of commands Comments on how to run labs. 8. ..<\/p>\n<div class=\"clear-fix\"><\/div>\n<p><a href=\"https:\/\/wiki.thomasandsofia.com\/?p=1973\" title=\"read more...\">Read more<\/a><\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[45],"tags":[],"class_list":["post-1973","post","type-post","status-publish","format-standard","hentry","category-icnd1-ccent"],"_links":{"self":[{"href":"https:\/\/wiki.thomasandsofia.com\/index.php?rest_route=\/wp\/v2\/posts\/1973","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/wiki.thomasandsofia.com\/index.php?rest_route=\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/wiki.thomasandsofia.com\/index.php?rest_route=\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/wiki.thomasandsofia.com\/index.php?rest_route=\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/wiki.thomasandsofia.com\/index.php?rest_route=%2Fwp%2Fv2%2Fcomments&post=1973"}],"version-history":[{"count":10,"href":"https:\/\/wiki.thomasandsofia.com\/index.php?rest_route=\/wp\/v2\/posts\/1973\/revisions"}],"predecessor-version":[{"id":2828,"href":"https:\/\/wiki.thomasandsofia.com\/index.php?rest_route=\/wp\/v2\/posts\/1973\/revisions\/2828"}],"wp:attachment":[{"href":"https:\/\/wiki.thomasandsofia.com\/index.php?rest_route=%2Fwp%2Fv2%2Fmedia&parent=1973"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/wiki.thomasandsofia.com\/index.php?rest_route=%2Fwp%2Fv2%2Fcategories&post=1973"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/wiki.thomasandsofia.com\/index.php?rest_route=%2Fwp%2Fv2%2Ftags&post=1973"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}